View CS438507_1125959.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CS4385
114 dB, 192 kHz 8-Channel D/A Converter
Features
Advanced Multi-bit Delta Sigma Architecture 24-bit Conversion Automatic Detection of Sample Rates up to 192 kHz 114 dB Dynamic Range -100 dB THD+N Direct Stream Digital Mode - Non-Decimating Volume Control - - On-Chip 50 kHz Filter Matched PCM and DSD Analog Output Levels
Description
The CS4385 is a complete 8-channel digital-to-analog system. This D/A system includes digital de-emphasis, half-dB step size volume control, ATAPI channel mixing, selectable fast and slow digital interpolation filters followed by an oversampled, multi-bit delta sigma modulator which includes mismatch-shaping technology that eliminates distortion due to capacitor mismatch. Following this stage is a multi-element switched capacitor stage and low-pass filter with differential analog outputs. The CS4385 also has a proprietary DSD processor which allows for volume control and 50 kHz on-chip filtering without an intermediate decimation stage. It also offers an optional path for direct DSD conversion by directly using the multi-element switched capacitor array. The CS4385 is available in a 48-pin LQFP package in both Commercial (-40 to +85) and Automotive (-40 to +105) grades. The CDB4385 Customer Demonstration board is also available for device evaluation and implementation suggestions. Please see "Ordering Information" on page 54 for complete details. The CS4385 accepts PCM data at sample rates from 4 kHz to 216 kHz, DSD audio data, and delivers excellent sound quality. These features are ideal for multichannel audio systems, including SACD players, A/V receivers, digital TV's, mixing consoles, effects processors, sound cards, and automotive audio systems.
Compatible with Industry-Standard Time Division Multiplexed (TDM) Serial Interface Selectable Digital Filters Volume Control with 1/2-dB Step Size and Soft Ramp Low Clock Jitter Sensitivity +5 V Analog Supply, +2.5 V Digital Supply Separate 1.8 to 5 V Logic Supplies for the Control & Serial Ports
C ontrol Port Supply = 1.8 V to 5 V
Digital Supply = 2.5 V
A nalog Supply = 5 V
Le ve l T ra nsla tor
Hardw are Mode or I2C /SPI Softw are Mode C ontrol Data
Register/Hardware C onfiguration
Inte rna l Voltage Re fe rence
Reset
Serial A udio Port Supply = 1.8 V to 5 V
S e ria l Inte rfa ce
TDM Serial A udio Input
DSD A udio Input
Le ve l T ra nsla tor
PC M Serial A udio Input
8
Volume C ontrols
Digital F ilters
Multi-bit Modula tors
Switch-C ap DAC a nd Analog F ilte rs
8
8
E ight C hannels of Differential O utputs
DSD Proce ssor -Volume control -50 kHz filter
E xte rna l Mute C ontrol
2
Mute Signals
http://www.cirrus.com
Copyright (c) Cirrus Logic, Inc. 2007 (All Rights Reserved)
APRIL '07 DS671F1
CS4385
TABLE OF CONTENTS
1. PIN DESCRIPTION ...................................................................................................................... 6 2. CHARACTERISTICS AND SPECIFICATIONS ...................................................................................... 8 RECOMMENDED OPERATING CONDITIONS ..................................................................................... 8 ABSOLUTE MAXIMUM RATINGS ......................................................................................................... 8 POWER AND THERMAL CHARACTERISTICS .................................................................................. 11 3. TYPICAL CONNECTION DIAGRAM .................................................................................................. 19 4. APPLICATIONS ................................................................................................................................... 21 4.1 Master Clock ................................................................................................................................... 21 4.2 Mode Select .................................................................................................................................... 22 4.3 Digital Interface Formats ................................................................................................................ 23 4.3.1 OLM #1 .................................................................................................................................. 24 4.3.2 OLM #2 .................................................................................................................................. 24 4.3.3 OLM #3 .................................................................................................................................. 25 4.3.4 OLM #4 .................................................................................................................................. 25 4.3.5 TDM ....................................................................................................................................... 26 4.4 Oversampling Modes ...................................................................................................................... 26 4.5 Interpolation Filter ........................................................................................................................... 26 4.6 De-Emphasis .................................................................................................................................. 27 4.7 ATAPI Specification ........................................................................................................................ 27 4.8 Direct Stream Digital (DSD) Mode .................................................................................................. 28 4.9 Grounding and Power Supply Arrangements ................................................................................. 29 4.9.1 Capacitor Placement ............................................................................................................. 29 4.10 Analog Output and Filtering .......................................................................................................... 29 4.11 The MUTEC Outputs .................................................................................................................... 30 4.12 Recommended Power-Up Sequence ........................................................................................... 31 4.12.1 Hardware Mode ................................................................................................................... 31 4.12.2 Software Mode .................................................................................................................... 32 4.13 Recommended Procedure for Switching Operational Modes ....................................................... 32 4.14 Control Port Interface ................................................................................................................... 32 4.14.1 MAP Auto Increment ........................................................................................................... 32 4.14.2 IC Mode .............................................................................................................................. 32 4.14.2.1 IC WriteTM ............................................................................................................... 33 4.14.2.2 IC Read .................................................................................................................. 33 4.14.3 SPITM Mode ......................................................................................................................... 34 4.14.3.1 SPI Write .................................................................................................................. 34 4.15 Memory Address Pointer (MAP) ............................................................................................. 34 4.15.1 INCR (Auto Map Increment Enable) .................................................................................... 34 4.15.2 MAP4-0 (Memory Address Pointer) .................................................................................... 34 5. REGISTER QUICK REFERENCE ....................................................................................................... 35 6. REGISTER DESCRIPTION .................................................................................................................. 37 6.1 Chip Revision (address 01h) ......................................................................................................... 37 6.1.1 Part Number ID (PART) [Read Only] .................................................................................... 37 6.2 Mode Control 1 (address 02h) ........................................................................................................ 37 6.2.1 Control Port Enable (CPEN) .................................................................................................. 37 6.2.2 Freeze Controls (FREEZE) ................................................................................................... 37 6.2.3 PCM/DSD Selection (DSD/PCM) .......................................................................................... 38 6.2.4 DAC Pair Disable (DACx_DIS) .............................................................................................. 38 6.2.5 Power Down (PDN) ............................................................................................................... 38 6.3 PCM Control (address 03h) ........................................................................................................... 38 6.3.1 Digital Interface Format (DIF) ................................................................................................ 38 6.3.2 Functional Mode (FM) ........................................................................................................... 39 6.4 DSD Control (address 04h) ........................................................................................................... 39 2 DS671F1
CS4385
6.4.1 DSD Mode Digital Interface Format (DSD_DIF) .................................................................... 39 6.4.2 Direct DSD Conversion (DIR_DSD) ...................................................................................... 40 6.4.3 Static DSD Detect (STATIC_DSD) ........................................................................................ 40 6.4.4 Invalid DSD Detect (INVALID_DSD) ..................................................................................... 40 6.4.5 DSD Phase Modulation Mode Select (DSD_PM_MODE) ..................................................... 40 6.4.6 DSD Phase Modulation Mode Enable (DSD_PM_EN) ......................................................... 40 6.5 Filter Control (address 05h) ........................................................................................................... 41 6.5.1 Interpolation Filter Select (FILT_SEL) ................................................................................... 41 6.6 Invert Control (address 06h) .......................................................................................................... 41 6.6.1 Invert Signal Polarity (Inv_xx) ................................................................................................ 41 6.7 Group Control (address 07h) ......................................................................................................... 41 6.7.1 Mutec Pin Control (MUTEC) .................................................................................................. 41 6.7.2 Channel A Volume = Channel B Volume (Px_A=B) .............................................................. 42 6.7.3 Single Volume Control (SNGLVOL) ...................................................................................... 42 6.8 Ramp and Mute (address 08h) ...................................................................................................... 42 6.8.1 Soft Ramp and Zero Cross CONTROL (SZC) ...................................................................... 42 6.8.2 Soft Volume Ramp-Up after Error (RMP_UP) ....................................................................... 43 6.8.3 Soft Ramp-Down before Filter Mode Change (RMP_DN) ..................................................... 43 6.8.4 PCM Auto-Mute (PAMUTE) .................................................................................................. 43 6.8.5 DSD Auto-Mute (DAMUTE) ................................................................................................... 44 6.8.6 MUTE Polarity and DETECT (MUTEP1:0) ............................................................................ 44 6.9 Mute Control (address 09h) ........................................................................................................... 44 6.9.1 Mute (MUTE_xx) ................................................................................................................... 44 6.10 Mixing Control (address 0Ah, 0Dh, 10h, 13h) ............................................................................. 45 6.10.1 De-Emphasis Control (PX_DEM1:0) ................................................................................... 45 6.11 ATAPI Channel Mixing and Muting (ATAPI) ................................................................................. 45 6.12 Volume Control (address 0Bh, 0Ch, 0Eh, 0Fh, 11h, 12h, 14h, 15h) ........................................... 46 6.12.1 Digital Volume Control (xx_VOL7:0) ................................................................................... 46 6.13 PCM Clock Mode (address 16h) ................................................................................................. 47 6.13.1 Master Clock DIVIDE by 2 ENABLE (MCLKDIV) ................................................................ 47 7. FILTER PLOTS ..................................................................................................................................... 48 8. PARAMETER DEFINITIONS ................................................................................................................ 52 9. PACKAGE DIMENSIONS ................................................................................................................... 53 10. ORDERING INFORMATION .............................................................................................................. 54 11. REFERENCES .................................................................................................................................... 54 12. REVISION HISTORY ......................................................................................................................... 55
DS671F1
3
CS4385
LIST OF FIGURES
Figure 1.Serial Audio Interface Timing ...................................................................................................... 15 Figure 2.TDM Serial Audio Interface Timing ............................................................................................. 15 Figure 3.Direct Stream Digital - Serial Audio Input Timing ........................................................................ 16 Figure 4.Direct Stream Digital - Serial Audio Input Timing for Phase Modulation Mode ........................... 16 Figure 5.Control Port Timing - IC Format ................................................................................................. 17 Figure 6.Control Port Timing - SPI Format ................................................................................................ 18 Figure 7.Typical Connection Diagram, Software Mode ............................................................................. 19 Figure 8.Typical Connection Diagram, Hardware ..................................................................................... 20 Figure 9.Format 0 - Left-Justified up to 24-bit Data .................................................................................. 23 Figure 10.Format 1 - IS up to 24-bit Data ................................................................................................ 23 Figure 11.Format 2 - Right-Justified 16-bit Data ....................................................................................... 23 Figure 12.Format 3 - Right-Justified 24-bit Data ....................................................................................... 23 Figure 13.Format 4 - Right-Justified 20-bit Data ....................................................................................... 23 Figure 14.Format 5 - Right-Justified 18-bit Data ....................................................................................... 24 Figure 15.Format 8 - One-Line Mode 1 ..................................................................................................... 24 Figure 16.Format 9 - One-Line Mode 2 ..................................................................................................... 24 Figure 17.Format 10 - One-Line Mode 3 ................................................................................................... 25 Figure 18.Format 11 - One Line Mode 4 ................................................................................................... 25 Figure 19.Format 12 - TDM Mode ............................................................................................................. 26 Figure 20.De-Emphasis Curve .................................................................................................................. 27 Figure 21.ATAPI Block Diagram (x = channel pair 1, 2, 3, or 4) ............................................................... 27 Figure 22.DSD Phase Modulation Mode Diagram .................................................................................... 28 Figure 23.Full-Scale Output ...................................................................................................................... 29 Figure 24.Recommended Output Filter ..................................................................................................... 30 Figure 25.Recommended Mute Circuitry .................................................................................................. 31 Figure 26.Control Port Timing, IC Mode .................................................................................................. 33 Figure 27.Control Port Timing, SPI Mode ................................................................................................. 34 Figure 28.Single-Speed (fast) Stopband Rejection ................................................................................... 48 Figure 29.Single-Speed (fast) Transition Band ......................................................................................... 48 Figure 30.Single-Speed (fast) Transition Band (detail) ............................................................................. 48 Figure 31.Single-Speed (fast) Passband Ripple ....................................................................................... 48 Figure 32.Single-Speed (slow) Stopband Rejection ................................................................................. 48 Figure 33.Single-Speed (slow) Transition Band ........................................................................................ 48 Figure 34.Single-Speed (slow) Transition Band (detail) ............................................................................ 49 Figure 35.Single-Speed (slow) Passband Ripple ...................................................................................... 49 Figure 36.Double-Speed (fast) Stopband Rejection ................................................................................. 49 Figure 37.Double-Speed (fast) Transition Band ........................................................................................ 49 Figure 38.Double-Speed (fast) Transition Band (detail) ............................................................................ 49 Figure 39.Double-Speed (fast) Passband Ripple ...................................................................................... 49 Figure 40.Double-Speed (slow) Stopband Rejection ................................................................................ 50 Figure 41.Double-Speed (slow) Transition Band ...................................................................................... 50 Figure 42.Double-Speed (slow) Transition Band (detail) .......................................................................... 50 Figure 43.Double-Speed (slow) Passband Ripple .................................................................................... 50 Figure 44.Quad-Speed (fast) Stopband Rejection .................................................................................... 50 Figure 45.Quad-Speed (fast) Transition Band .......................................................................................... 50 Figure 46.Quad-Speed (fast) Transition Band (detail) .............................................................................. 51 Figure 47.Quad-Speed (fast) Passband Ripple ........................................................................................ 51 Figure 48.Quad-Speed (slow) Stopband Rejection ................................................................................... 51 Figure 49.Quad-Speed (slow) Transition Band ......................................................................................... 51 Figure 50.Quad-Speed (slow) Transition Band (detail) ............................................................................. 51 Figure 51.Quad-Speed (slow) Passband Ripple ....................................................................................... 51
4
DS671F1
CS4385
LIST OF TABLES
Table 1. Single-Speed Mode Standard Frequencies ................................................................................ 21 Table 2. Double-Speed Mode Standard Frequencies ............................................................................... 21 Table 3. Quad-Speed Mode Standard Frequencies ................................................................................. 21 Table 4. PCM Digital Interface Format, Hardware Mode Options ............................................................. 22 Table 5. Mode Selection, Hardware Mode Options .................................................................................. 22 Table 6. Direct Stream Digital (DSD), Hardware Mode Options ............................................................... 22 Table 7. Digital Interface Formats - PCM Mode ........................................................................................ 39 Table 8. Digital Interface Formats - DSD Mode ........................................................................................ 39 Table 9. ATAPI Decode Table .................................................................................................................. 45 Table 10. Example Digital Volume Settings .............................................................................................. 46
DS671F1
5
CS4385 1. PIN DESCRIPTION
DSDA4 DSDB4 VLS DSD_SCLK MUTEC1 AOUTA1AOUTA1+ AOUTB1+ DSDB2 DSDA3 DSDB3 AOUTB1-
48 47 46 45 44 43 42 41 40 39 38 37 DSDA2 DSDB1 DSDA1 VD GND MCLK LRCK SDIN1 SCLK M4(TST) SDIN2 M3(TST) 1 2 3 4 5 6 7 8 9 10 11 12 36 35 34 33 32 AOUTA2AOUTA2+ AOUTB2+ AOUTB2VA GND AOUTA3AOUTA3+ AOUTB3+ AOUTB3AOUTA4AOUTA4+
CS4385
31 30 29 28 27 26 25
13 14 15 16 17 18 19 20 21 22 23 24 SDIN3 SDIN4 M2(SCL/CCLK) M1(SDA/CDIN) M0(AD0/CS) VQ MUTEC234 AOUTB4AOUTB4+ RST FILT+ VLC
Pin Name
VD GND MCLK LRCK SDIN1 SDIN2 SDIN3 SDIN4 SCLK VLC RST FILT+
#
4 5 31 6 7 8 11 13 14 9 18 19 20
Pin Description
Digital Power (Input) - Positive power supply for the digital section. Refer to the Recommended Operating Conditions for appropriate voltages. Ground (Input) - Ground reference. Should be connected to analog ground. Master Clock (Input) - Clock source for the delta-sigma modulator and digital filters. Tables 1-3 illustrate several standard audio sample rates and the required master clock frequency. Left Right Clock (Input) - Determines which channel, Left or Right, is currently active on the serial audio data line. The frequency of the left/right clock must be at the audio sample rate, Fs. Serial Audio Data Input (Input) - Input for two's complement serial audio data. Serial Clock (Input) - Serial clock for the serial audio interface. Control Port Power (Input) - Determines the required signal level for the control port. Refer to the Recommended Operating Conditions for appropriate voltages. Reset (Input) - The device enters a low power mode and all internal registers are reset to their default settings when low. Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling circuits. Requires the capacitive decoupling to analog ground, as shown in the Typical Connection Diagram. Quiescent Voltage (Output) - Filter connection for internal quiescent voltage. VQ must be capacitively coupled to analog ground, as shown in the Typical Connection Diagram. The nominal voltage level is specified in the Analog Characteristics and Specifications section. VQ presents an appreciable source impedance and any current drawn from this pin will alter device performance. However, VQ can be used to bias the analog circuitry assuming there is no AC signal component and the DC current is less than the maximum specified in the Analog Characteristics and Specifications section. Mute Control (Output) - The Mute Control pins go high during power-up initialization, reset, muting, power-down or if the master clock to left/right clock frequency ratio is incorrect. These pins are intended to be used as a control for external mute circuits to prevent the clicks and pops that can occur in any single supply system. The use of external mute circuits are not mandatory but may be desired for designs requiring the absolute minimum in extraneous clicks and pops.
VQ
21
MUTEC1 MUTEC234
41 22
6
DS671F1
CS4385
Pin Name
AOUTA1 +,AOUTB1 +,AOUTA2 +,AOUTB2 +,AOUTA3 +,AOUTB3 +,AOUTA4 +,AOUTB4 +,VA VLS
#
Pin Description
39, 40 38, 37 35, 36 34, 33 Differential Analog Output (Output) - The full-scale differential analog output level is specified in the 29, 30 Analog Characteristics specification table. 28, 27 25, 26 24, 23 32 43 Analog Power (Input) - Positive power supply for the analog section. Refer to the Recommended Operating Conditions for appropriate voltages. Serial Audio Interface Power (Input) - Determines the required signal level for the serial audio interface. Refer to the Recommended Operating Conditions for appropriate voltages. Serial Control Port Clock (Input) - Serial clock for the serial control port. Requires an external pullup resistor to the logic interface voltage in IC Mode as shown in the Typical Connection Diagram. Serial Control Data (Input/Output) - SDA is a data I/O line in IC Mode and requires an external pullup resistor to the logic interface voltage, as shown in the Typical Connection Diagram. CDIN is the input data line for the control port interface in SPI Mode. Address Bit 0 (IC) / Chip Select (SPI) (Input) - AD0 is a chip address pin in IC Mode; CS is the chip select signal for SPI format. Test (Input) - These pins are not used in Software Mode and should not be left floating (connect to ground).
Software Mode Definitions SCL/CCLK SDA/CDIN AD0/CS TST 15 16 17 10, 12
Hardware Mode Definitions M0 M1 M2 M3 M4 DSD Definitions DSD_SCLK DSDA1 DSDB1 DSDA2 DSDB2 DSDA3 DSDB3 DSDA4 DSDB4 42 3 2 1 48 47 46 45 44 DSD Serial Clock (Input) - Serial clock for the Direct Stream Digital audio interface. 17 16 15 12 10 Mode Selection (Input) - Determines the operational mode of the device as detailed in Tables 4 and 5.
Direct Stream Digital Input (Input) - Input for Direct Stream Digital serial audio data.
DS671F1
7
CS4385 2. CHARACTERISTICS AND SPECIFICATIONS RECOMMENDED OPERATING CONDITIONS
GND = 0 V; all voltages with respect to ground. Parameters
DC Power Supply Analog power Digital internal power Serial data port interface power Control port interface power Ambient Operating Temperature (Power Applied) Commercial Grade (-CQZ) Automotive Grade (-DQZ)
Symbol
VA VD VLS VLC TA
Min
4.75 2.37 1.71 1.71 -40 -40
Typ
5.0 2.5 5.0 5.0 -
Max
5.25 2.63 5.25 5.25 + 85 +105
Units
V V V V C C
ABSOLUTE MAXIMUM RATINGS
GND = 0 V; all voltages with respect to ground. Parameters
Analog power Digital internal power Serial data port interface power Control port interface power Input Current Any Pin Except Supplies Digital Input Voltage Serial data port interface Control port interface Ambient Operating Temperature (Power Applied) Storage Temperature DC Power Supply
Symbol
VA VD VLS VLC Iin VIND-S VIND-C Top Tstg
Min
-0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -55 -65
Max
6.0 3.2 6.0 6.0 10 VLS+ 0.4 VLC+ 0.4 125 150
Units
V V V V mA V V C C
WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes.
8
DS671F1
CS4385 DAC ANALOG CHARACTERISTICS - COMMERCIAL (-CQZ)
Test Conditions (unless otherwise specified): VA = VLS = VLC = 5 V; VD = 2.5 V; TA = 25C; Full-scale 997 Hz input sine wave (Note 1); Tested under max ac-load resistance; Valid with FILT+ and VQ capacitors as shown in "Typical Connection Diagram" on page 19; Measurement Bandwidth 10 Hz to 20 kHz. Parameters Fs = 48 kHz, 96 kHz, 192 kHz and DSD
Dynamic Range A-weighted unweighted 16-bit A-weighted (Note 2) unweighted 24-bit 0 dB -20 dB -60 dB THD+N 0 dB -20 dB -60 dB A-weighted (1 kHz) 24-bit 108 105 114 111 97 94 -100 -91 -51 -94 -74 -34 114 110 0.1 100 -94 -45 dB dB dB dB dB dB dB dB dB dB dB dB dB ppm/ C Vpp Vpp mA k pF VDC A
Symbol
Min
Typ
Max
Unit
Total Harmonic Distortion + Noise
(Note 2) 16-bit
Idle Channel Noise / Signal-to-noise ratio Interchannel Isolation
DC Accuracy
Interchannel Gain Mismatch Gain Drift
Analog Output
Full-Scale DifferentialOutput Voltage (Note 3) Output Impedance Max DC Current draw from an AOUT pin Min AC-Load Resistance Max Load Capacitance Quiescent Voltage Max Current draw from VQ PCM, DSD processor Direct DSD Mode VFS ZOUT IOUTmax RL CL VQ IQMAX 1.28*VA 0.90*VA 1.32*VA 0.94*VA 130 1.0 3 100 50% VA 10 1.36*VA 0.98*VA -
Notes: 1. One-half LSB of triangular PDF dither is added to data. 2. Performance limited by 16-bit quantization noise. 3. VFS is tested under load RL and includes attenuation due to ZOUT.
DS671F1
9
CS4385 DAC ANALOG CHARACTERISTICS - AUTOMOTIVE (-DQZ)
Test Conditions (unless otherwise specified): VA = 4.75 to 5.25 V; VLS = 1.71 to 5.25 V; VLC = 1.71 to 5.25 V; VD = 2.37 to 2.63 V; TA = -40C to 85C; Full-scale 997 Hz input sine wave (Note 1); Tested under max ac-load resistance; Valid with FILT+ and VQ capacitors as shown in "Typical Connection Diagram" on page 19; Measurement Bandwidth 10 Hz to 20 kHz. Parameters Fs = 48 kHz, 96 kHz, 192 kHz and DSD
Dynamic Range (Note 1) 24-bit
Symbol
Min
105 102 1.28*VA 0.90*VA -
Typ
114 111 97 94 -100 -91 -51 -94 -74 -34 114 110 0.1 100 1.32*VA 0.94*VA 130 1.0 3 100 50% VA 10
Max
-91 -42 1.36*VA 0.98*VA -
Units
dB dB dB dB dB dB dB dB dB dB dB dB dB ppm/C Vpp Vpp mA k pF VDC A
A-weighted unweighted 16-bit A-weighted (Note 2) unweighted Total Harmonic Distortion + Noise (Note 1) 24-bit 0 dB -20 dB -60 dB THD+N (Note 2) 16-bit 0 dB -20 dB -60 dB Idle Channel Noise / Signal-to-noise ratio A-weighted Interchannel Isolation (1 kHz)
DC Accuracy
Interchannel Gain Mismatch Gain Drift
Analog Output
Full-Scale DifferentialPCM, DSD processor VFS Output Voltage (Note 3) Direct DSD Mode Output Impedance ZOUT Max DC Current draw from an AOUT pin IOUTmax Min AC-Load Resistance RL Max Load Capacitance CL Quiescent Voltage VQ Max Current draw from VQ IQMAX
10
DS671F1
CS4385 POWER AND THERMAL CHARACTERISTICS
Parameters Power Supplies
Power Supply Current (Note 4) normal operation, VA= 5 V VD= 2.5 V (Note 5) Interface current, VLC=5 V VLS=5 V (Note 6) power-down state (all supplies) Power Dissipation (Note 4) VA = 5 V, VD = 2.5 V normal operation (Note 6) power-down Package Thermal Resistance (1 kHz) (60 Hz) IA ID ILC ILS Ipd 84 20 2 75 200 470 1 48 15 60 40 91 25 520 mA mA A A A mW mW C/Watt C/Watt dB dB
Symbol
Min
Typ
Max
Units
JA JC PSRR
Power Supply Rejection Ratio (Note 7)
Notes: 4. Current consumption increases with increasing Fs within a given speed mode and is signal dependant. Max values are based on highest Fs and highest MCLK. 5. ILC measured with no external loading on the SDA pin. 6. Power-Down Mode is defined as RST pin = Low with all clock and data lines held static. 7. Valid with the recommended capacitor values on FILT+ and VQ as shown in Figures 7 and 8.
DS671F1
11
CS4385 COMBINED INTERPOLATION & ON-CHIP ANALOG FILTER RESPONSE
The filter characteristics have been normalized to the sample rate (Fs) and can be referenced to the desired sample rate by multiplying the given characteristic by Fs. See Note 12. Fast Roll-Off Parameter Unit Min Typ Max Combined Digital and On-chip Analog Filter Response - Single-Speed Mode - 48 kHz
Passband (Note 9) Frequency Response StopBand StopBand Attenuation Group Delay De-emphasis Error (Note 11) (Relative to 1 kHz) Fs = 32 kHz Fs = 44.1 kHz Fs = 48 kHz to -0.01 dB corner to -3 dB corner 10 Hz to 20 kHz (Note 10) (Note 10) to -0.01 dB corner to -3 dB corner 10 Hz to 20 kHz 0 0 -0.01 0.547 102 0 0 -0.01 .583 80 to -0.01 dB corner to -3 dB corner 10 Hz to 20 kHz (Note 10) 0 0 -0.01 .635 90 10.4/Fs 6.15/Fs 7.1/Fs .454 .499 +0.01 0.36 0.21 0.14 .430 .499 +0.01 .105 .490 +0.01 Fs Fs dB Fs dB s dB dB dB Fs Fs dB Fs dB s Fs Fs dB Fs dB s
Combined Digital and On-chip Analog Filter Response - Double-Speed Mode - 96 kHz
Passband (Note 9) Frequency Response StopBand StopBand Attenuation Group Delay Passband (Note 9) Frequency Response StopBand StopBand Attenuation Group Delay
Combined Digital and On-chip Analog Filter Response - Quad-Speed Mode - 192 kHz
Notes: 8. Slow roll-off interpolation filter is only available in Software Mode. 9. Response is clock-dependent and will scale with Fs. 10. For Single-Speed Mode, the Measurement Bandwidth is from stopband to 3 Fs. For Double-Speed Mode, the Measurement Bandwidth is from stopband to 3 Fs. For Quad-Speed Mode, the Measurement Bandwidth is from stopband to 1.34 Fs. 11. De-emphasis is available only in Single-Speed Mode; only 44.1 kHz De-emphasis is available in Hardware Mode. 12. Amplitude vs. Frequency plots of this data are available in Section 7. "Filter Plots" on page 48 .
12
DS671F1
CS4385 COMBINED INTERPOLATION & ON-CHIP ANALOG FILTER RESPONSE (CONTINUED)
Parameter Single-Speed Mode - 48 kHz
Passband (Note 9) Frequency Response StopBand StopBand Attenuation Group Delay De-emphasis Error (Note 11) (Relative to 1 kHz) Fs = 32 kHz Fs = 44.1 kHz Fs = 48 kHz to -0.01 dB corner to -3 dB corner 10 Hz to 20 kHz (Note 10) (Note 10) to -0.01 dB corner to -3 dB corner 10 Hz to 20 kHz 0 0 -0.01 .583 64 0 0 -0.01 .792 70 to -0.01 dB corner to -3 dB corner 10 Hz to 20 kHz (Note 10) 0 0 -0.01 .868 75 7.8/Fs 5.4/Fs 6.6/Fs 0.417 0.499 +0.01 0.36 0.21 0.14 .296 .499 +0.01 .104 .481 +0.01 Fs Fs dB Fs dB s dB dB dB Fs Fs dB Fs dB s Fs Fs dB Fs dB s
Slow Roll-Off (Note 8) Min Typ Max
Unit
Double-Speed Mode - 96 kHz
Passband (Note 9) Frequency Response StopBand StopBand Attenuation Group Delay
Quad-Speed Mode - 192 kHz
Passband (Note 9) Frequency Response StopBand StopBand Attenuation Group Delay
DSD COMBINED DIGITAL & ON-CHIP ANALOG FILTER RESPONSE
Parameter DSD Processor Mode
Passband (Note 9) Frequency Response Roll-off to -3 dB corner 10 Hz to 20 kHz 0 -0.05 27 to -0.1 dB corner to -3 dB corner 0 0 -0.1 50 +0.05 26.9 176.4 0 kHz dB dB/Oct kHz kHz dB
Min
Typ
Max
Unit
Direct DSD Mode
Passband (Note 9) Frequency Response 10 Hz to 20 kHz
DS671F1
13
CS4385 DIGITAL CHARACTERISTICS
Parameters
Input Leakage Current Input Capacitance High-Level Input Voltage Low-Level Input Voltage Low-Level Output Voltage (IOL = -1.2 mA) MUTEC auto detect input high voltage MUTEC auto detect input low voltage Maximum MUTEC Drive Current MUTEC High-Level Output Voltage MUTEC Low-Level Output Voltage (Note 13) Serial I/O Control I/O Serial I/O Control I/O Control I/O = 3.3 V, 5 V
Symbol
Iin VIH VIH VIL VIL VOL VOL VIH VIL Imax VOH VOL
Min
0.70*VLS 0.70*VLC 0.70*VA -
Typ
8 3 VA 0
Max
10 0.30*VLS 0.30*VLC 0.20*VLC 0.25*VLC 0.30*VA -
Units
A pF V V V V V V V V mA V V
Low-Level Output Voltage (IOL = -1.2 mA) Control I/O = 1.8 V, 2.5 V
Notes: 13. Any pin except supplies. Transient currents of up to 100 mA on the input pins will not cause SCR latchup.
14
DS671F1
CS4385 SWITCHING CHARACTERISTICS - PCM
Inputs: Logic 0 = GND, Logic 1 = VLS, CL = 20 pF. Parameters
RST pin Low Pulse Width MCLK Frequency MCLK Duty Cycle Input Sample Rate - LRCK (Manual selection) (Note 15) Single-Speed Mode Double-Speed Mode Quad-Speed Mode Single-Speed Mode Double-Speed Mode Quad-Speed Mode (Note 16) tsckh tsckl tlcks tlckd (Note 17) tlpw tds tdh Fs Fs Fs Fs Fs Fs (Note 14)
Symbol
Min
1 1.024 45 4 50 100 4 84 170 45 45 8 8 5 5 1/fSCLK 3 5
Max
55.2 55 54 108 216 54 108 216 55 55 7/fSCLK -
Units
ms MHz % kHz kHz kHz kHz kHz kHz % % ns ns ns ns ns ns ns
Input Sample Rate - LRCK (Auto detect)
LRCK Duty Cycle SCLK Duty Cycle SCLK High Time SCLK Low Time LRCK Edge to SCLK Rising Edge SCLK Rising Edge to LRCK Falling Edge TDM LRCK hightime pulse SDIN Setup Time Before SCLK Rising Edge SDIN Hold Time After SCLK Rising Edge
Notes: 14. After powering up, RST should be held low until after the power supplies and clocks are settled. 15. See Tables 1 - 3 for suggested MCLK frequencies. 16. Not valid for TDM Mode. 17. MSB of CH1 is always the second SCLK rising edge following LRCK rising edge.
t lp w
LRCK
tlcks
tsckh
tsckl
LR C K t lc k s t sckh ts ckl t lc k d t lc k s
SCLK
SC LK
tds
SDINx
tdh
MSB MSB-1
S D IN 1
tds
tdh MSB M S B -1
Figure 1. Serial Audio Interface Timing
Figure 2. TDM Serial Audio Interface Timing
DS671F1
15
CS4385 SWITCHING CHARACTERISTICS - DSD
Logic 0 = GND; Logic 1 = VLS; CL = 20 pF. Parameter
MCLK Duty Cycle DSD_SCLK Pulse Width Low DSD_SCLK Pulse Width High DSD_SCLK Frequency
Symbol
tsclkl tsclkh
Min
40 160 160 1.024 2.048 20 20 -20
Typ
-
Max
60 3.2 6.4 20
Unit
% ns ns MHz MHz ns ns ns
(64x Oversampled) (128x Oversampled) DSD_A / _B valid to DSD_SCLK rising setup time DSD_SCLK rising to DSD_A or DSD_B hold time DSD clock to data transition (Phase Modulation Mode)
tsdlrs tsdh tdpm
t sclkh t sclkl DSD_SCLK t sdlrs
DSDxx
t sdh
Figure 3. Direct Stream Digital - Serial Audio Input Timing
t dpm DSD_SCLK (128Fs) DSD_SCLK (64Fs)
t dpm
DSDxx
Figure 4. Direct Stream Digital - Serial Audio Input Timing for Phase Modulation Mode
16
DS671F1
CS4385 SWITCHING CHARACTERISTICS - CONTROL PORT - IC FORMAT
Inputs: Logic 0 = GND, Logic 1 = VLC, CL = 20 pF. Parameter
SCL Clock Frequency RST Rising Edge to Start Bus Free Time Between Transmissions Start Condition Hold Time (prior to first clock pulse) Clock Low time Clock High Time Setup Time for Repeated Start Condition SDA Hold Time from SCL Falling SDA Setup time to SCL Rising Rise Time of SCL and SDA Fall Time SCL and SDA Setup Time for Stop Condition Acknowledge Delay from SCL Falling (Note 18)
Symbol
fscl tirs tbuf thdst tlow thigh tsust thdd tsud trc, trc tfc, tfc tsusp tack
Min
500 4.7 4.0 4.7 4.0 4.7 0 250 4.7 300
Max
100 1 300 1000
Unit
kHz ns s s s s s s ns s ns s ns
Notes: 18. Data must be held for sufficient time to bridge the transition time, tfc, of SCL.
RST t irs Stop SDA t buf
SCL Repeated Start
Start
Stop
t hdst
t high
t
hdst
tf
t susp
t
low
t
hdd
t sud
t sust
tr
Figure 5. Control Port Timing - IC Format
DS671F1
17
CS4385 SWITCHING CHARACTERISTICS - CONTROL PORT - SPITM FORMAT
Inputs: Logic 0 = GND, Logic 1 = VLC, CL = 20 pF. Parameter
CCLK Clock Frequency RST Rising Edge to CS Falling CCLK Edge to CS Falling CS High Time Between Transmissions CS Falling to CCLK Edge CCLK Low Time CCLK High Time CDIN to CCLK Rising Setup Time CCLK Rising to DATA Hold Time Rise Time of CCLK and CDIN Fall Time of CCLK and CDIN (Note 20) (Note 21) (Note 21) (Note 19)
Symbol
fsclk tsrs tspi tcsh tcss tscl tsch tdsu tdh tr2 tf2
Min
500 500 1.0 20 66 66 40 15 -
Max
6 100 100
Unit
MHz ns ns s ns ns ns ns ns ns ns
Notes: 19. tspi is only needed before first falling edge of CS after RST rising edge. tspi = 0 at all other times. 20. Data must be held for sufficient time to bridge the transition time of CCLK. 21. For FSCK < 1 MHz.
RST
t srs
CS t spi t css CCLK t r2
CDIN
t scl
t sch
t csh
t f2
t dsu t dh
Figure 6. Control Port Timing - SPI Format
18
DS671F1
CS4385 3. TYPICAL CONNECTION DIAGRAM
+2.5 V 1 F + 0.1 F 4 VD 32 VA AOUTA1+ AOUTA1AOUTB1+ 6 7 PCM Digital Audio Source 9 8 11 13 14
470
+5 V 0.1 F + 1 F
39 40 38 37 35 36 34 33 29 30 28 27 25 26 24 23
Analog Conditioning and Muting
220
MCLK LRCK SCLK SDIN1 SDIN2 SDIN3 SDIN4
AOUTB1AOUTA2+ AOUTA2AOUTB2+ AOUTB2AOUTA3+
Analog Conditioning and Muting
Analog Conditioning and Muting
Analog Conditioning and Muting
+1.8 V to +5 V
43 0.1 F
470
VLS
AOUTA3-
Analog Conditioning and Muting
CS4385
AOUTB3+ AOUTB3-
Analog Conditioning and Muting
3 2 1
DSDA1 DSDB1 DSDA2 DSDB2 DSDA3 DSDB3 DSDA4 DSDB4 DSD_SCLK MUTEC1 AOUTA4+ AOUTA4AOUTB4+ AOUTB4-
Analog Conditioning and Muting
DSD Audio Source
48 47 46 45 44 42
Analog Conditioning and Muting
41
MUTEC234 22
Mute Drive
19 MicroController 15 16 17 2 K 2 K
RST SCL/CCLK SDA/CDIN ADO/CS
Note* 18 0.1 F
FILT+ 20 VLC VQ 21 0.1 F + 1 F 0.1 F + 47 F
+1.8 V to +5 V
Note: Necessary for I 2C control port operation
GND 5
GND 31
TST*
NoteTST: Pins 10, 12
Figure 7. Typical Connection Diagram, Software Mode
DS671F1
19
CS4385
+2.5 V 1 F + 0.1 F 4 VD 32 VA AOUTA1+ AOUTA1AOUTB1+ 6 7 PCM Digital Audio Source 9 8 11 13 14
470
+5 V 0.1 F + 1 F
39 40 38 37 Analog Conditioning and Muting Analog Conditioning and Muting
220
MCLK LRCK SCLK SDIN1 SDIN2 SDIN3 SDIN4 VLS
AOUTB1-
MUTEC1
41
Mute Drive
AOUTA2+ AOUTA2AOUTB2+
35 36 34 33 29 30 28 27 25 26 24 23 Analog Conditioning and Muting Analog Conditioning and Muting Analog Conditioning and Muting Analog Conditioning and Muting
+1.8 V to +5 V
43 0.1 F
470
CS4385
3 2 1 DSDA1 DSDB1 DSDA2 DSDB2 DSDA3 DSDB3 DSDA4 DSDB4 DSD_SCLK
AOUTB2AOUTA3+ AOUTA3AOUTB3+ AOUTB3AOUTA4+ AOUTA4AOUTB4+ AOUTB4-
Analog Conditioning and Muting
Analog Conditioning and Muting
DSD Audio Source
48 47 46 45 44 42 Optional 47 K
10 12
M4 M3 M2 M1 M0 RST MUTEC234
22
Mute Drive
Stand-Alone Mode Configuration
15 16 17 19
FILT+ 20 VQ +1.8 V to +5 V 18 0.1 F VLC 21 0.1 F + 1 F 0.1 F + 47 F
GND 5
GND 31
Figure 8. Typical Connection Diagram, Hardware
20
DS671F1
CS4385 4. APPLICATIONS
The CS4385 serially accepts two's complement formatted PCM data at standard audio sample rates including 48, 44.1 and 32 kHz in SSM, 96, 88.2 and 64 kHz in DSM, and 192, 176.4 and 128 kHz in QSM. Audio data is input via the serial data input pins (SDINx). The Left/Right Clock (LRCK) determines which channel is currently being input on SDINx, and the Serial Clock (SCLK) clocks audio data into the input data buffer. For more information on serial audio interfaces, see Cirrus Application Note AN282, "The 2-Channel Serial Audio Interface: A Tutorial." The CS4385 can be configured in Hardware Mode by the M0, M1, M2 , M3 and M4 pins and in Software Mode through IC or SPI.
4.1
Master Clock
MCLK/LRCK must be an integer ratio as shown in Tables 1 - 3. The LRCK frequency is equal to Fs, the frequency at which words for each channel are input to the device. The MCLK-to-LRCK frequency ratio and speed mode is detected automatically during the initialization sequence by counting the number of MCLK transitions during a single LRCK period and by detecting the absolute speed of MCLK. Internal dividers are then set to generate the proper internal clocks. Tables 1 - 3 illustrate several standard audio sample rates and the required MCLK and LRCK frequencies. Please note there is no required phase relationship, but MCLK, LRCK and SCLK must be synchronous. Sample Rate (kHz)
32 44.1 48
256x
8.1920 11.2896 12.2880
384x
12.2880 16.9344 18.4320
MCLK (MHz) 512x 768x
16.3840 22.5792 24.5760 24.5760 33.8688 36.8640
1024x
32.7680 45.1584 49.1520
1152x
36.8640
Table 1. Single-Speed Mode Standard Frequencies
Sample Rate (kHz)
64 88.2 96
128x
192x
MCLK (MHz) 256x
384x
512x
32.7680 45.1584 49.1520
8.1920 12.2880 16.3840 24.5760 11.2896 16.9344 22.5792 33.8688 12.2880 18.4320 24.5760 36.8640 Table 2. Double-Speed Mode Standard Frequencies
Sample Rate (kHz)
176.4 192
64x
11.2896 12.2880
96x
16.9344 18.4320
MCLK (MHz) 128x
22.5792 24.5760
192x
33.8688 36.8640
256x
45.1584 49.1520
Table 3. Quad-Speed Mode Standard Frequencies = Denotes clock ratio and sample rate combinations which are NOT supported under auto speed-mode detection. Please see "Switching Characteristics - PCM" on page 15.
DS671F1
21
CS4385
4.2 Mode Select
In Hardware Mode, operation is determined by the Mode Select pins. The state of these pins are continually scanned for any changes. These pins require connection to supply or ground as outlined in 8. For M0, M1, M2 supply is VLC and for M3 and M4 supply is VLS. Tables 4 - 6 show the decode of these pins. In Software Mode, the operational mode and data format are set in the FM and DIF registers. See "Filter Plots" on page 48 . M1 (DIF1)
0 0 1 1
M0 (DIF0)
0 1 0 1
DESCRIPTION
Left-Justified, up to 24-bit data IS, up to 24-bit data Right-Justified, 16-bit Data Right-Justified, 24-bit Data
FORMAT
0 1 2 3
FIGURE
9 10 11 12
Table 4. PCM Digital Interface Format, Hardware Mode Options
M4
0 0 0 0 1 1 1
M3
0 0 1 1 0 0 1
M2 (DEM)
0 1 0 1 0 1 X
DESCRIPTION
Single-Speed without De-Emphasis (4 to 50 kHz sample rates) Single-Speed with 44.1 kHz De-Emphasis; see Figure 20 Double-Speed (50 to 100 kHz sample rates) Quad-Speed (100 to 200 kHz sample rates) Auto Speed-Mode Detect (32 kHz to 200 kHz sample rates) Auto Speed-Mode Detect with 44.1 kHz De-Emphasis; see Figure 20 DSD Processor Mode (see Table 6 for details)
Table 5. Mode Selection, Hardware Mode Options
M2
0 0 0 0 1 1 1 1
M1
0 0 1 1 0 0 1 1
M0
0 1 0 1 0 1 0 1
DESCRIPTION 64x oversampled DSD data with a 4x MCLK to DSD data rate 64x oversampled DSD data with a 6x MCLK to DSD data rate 64x oversampled DSD data with a 8x MCLK to DSD data rate 64x oversampled DSD data with a 12x MCLK to DSD data rate 128x oversampled DSD data with a 2x MCLK to DSD data rate 128x oversampled DSD data with a 3x MCLK to DSD data rate 128x oversampled DSD data with a 4x MCLK to DSD data rate 128x oversampled DSD data with a 6x MCLK to DSD data rate
Table 6. Direct Stream Digital (DSD), Hardware Mode Options
22
DS671F1
CS4385
4.3 Digital Interface Formats
The serial port operates as a slave and supports the IS, Left-Justified, Right-Justified, One-Line Mode (OLM) and TDM digital interface formats with varying bit depths from 16 to 32, as shown in Figures 9-19. Data is clocked into the DAC on the rising edge. OLM and TDM configurations are only supported in Software Mode.
LRCK SCLK Left Channel Right Channel
SDINx
MSB
-1 -2 -3 -4 -5
+5 +4 +3 +2 +1
LSB
MSB
-1 -2 -3 -4
+5 +4 +3 +2 +1
LSB
Figure 9. Format 0 - Left-Justified up to 24-bit Data
LRCK SCLK
Left Channel
Right Channel
SDINx
MSB
-1 -2 -3 -4 -5
+5 +4 +3 +2 +1
LSB
MSB
-1 -2 -3 -4
+5 +4 +3 +2 +1 LSB
Figure 10. Format 1 - IS up to 24-bit Data
LRCK
Left Channel
Right Channel
SCLK
SDINx
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
32 clocks
Figure 11. Format 2 - Right-Justified 16-bit Data
LRCK
Left Channel
Right Channel
SCLK
SDINx
0
23 22 21 20 19 18
76543210
23 22 21 20 19 18
76543210
32 clocks
Figure 12. Format 3 - Right-Justified 24-bit Data
Right Channel
LRCK
Left Channel
SCLK
SDINx
10
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
32 clocks
Figure 13. Format 4 - Right-Justified 20-bit Data
DS671F1
23
CS4385
LRCK
Left Channel
Right Channel
SCLK
SDINx
10
17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
32 clocks
Figure 14. Format 5 - Right-Justified 18-bit Data
4.3.1
OLM #1
OLM #1 serial audio interface format operates in Single-, Double-, or Quad-Speed Mode and will slave to SCLK at 128 Fs. Six channels of MSB first 20-bit PCM data are input on SDIN1. The last two channels are input on SDIN4.
64 clks LRCK SCLK SDIN1 MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB DAC_A1 20 clks SDIN4 DAC_A4 20 clks DAC_A2 20 clks DAC_A3 20 clks DAC_B1 20 clks DAC_B4 20 clks DAC_B2 20 clks DAC_B3 20 clks 64 clks
Left Channel
Right Channel
Figure 15. Format 8 - One-Line Mode 1
4.3.2
OLM #2
OLM #2 serial audio interface format operates in Single-, Double-, or Quad-Speed Mode and will slave to SCLK at 256 Fs. Six channels of MSB first 24-bit PCM data are input on SDIN1. The last two channels are input on SDIN4.
128 clks LRCK SCLK SDIN1 MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB DAC_A1 24 clks SDIN4 DAC_A4 24 clks DAC_A2 24 clks DAC_A3 24 clks DAC_B1 24 clks DAC_B4 24 clks DAC_B2 24 clks DAC_B3 24 clks 128 clks
Left Channel
Right Channel
Figure 16. Format 9 - One-Line Mode 2
24
DS671F1
CS4385
4.3.3 OLM #3
OLM #3 serial audio interface format operates in Single-, Double-, or Quad-Speed Mode and will slave to SCLK at 256 Fs. Eight channels of MSB first 20-bit PCM data are input on SDIN1.
128 clks LRCK SCLK SDIN1 MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB DAC_A1 20 clks DAC_A2 20 clks DAC_A3 20 clks DAC_A4 20 clks DAC_B1 20 clks DAC_B2 20 clks DAC_B3 20 clks DAC_B4 20 clks 128 clks
Left Channel
Right Channel
Figure 17. Format 10 - One-Line Mode 3
4.3.4
OLM #4
OLM #4 serial audio interface format operates in Single-, Double-, or Quad-Speed Mode and will slave to SCLK at 256 Fs. Eight channels of MSB first 24-bit PCM data are input on SDIN1.
128 clks LRCK SCLK SDIN1 MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB DAC_A1 24 clks DAC_A2 24 clks DAC_A3 24 clks DAC_A4 24 clks DAC_B1 24 clks DAC_B2 24 clks DAC_B3 24 clks DAC_B4 24 clks 128 clks
Left Channel
Right Channel
Figure 18. Format 11 - One Line Mode 4
DS671F1
25
CS4385
4.3.5 TDM
The TDM serial audio interface format operates in Single-, Double-, or Quad-Speed Mode and will slave to SCLK at 256 Fs. Data is received most significant bit first on the first SCLK after an LRCK transition and is valid on the rising edge of SCLK. LRCK identifies the start of a new frame and is equal to the sample rate, Fs. LRCK is sampled as valid on the rising SCLK edge preceding the most significant bit of the first data sample and must be held valid for one SCLK period. Each time slot is 32 bits wide, with the valid data sample left-justified within the time slot with the remaining bits being zero-padded.
256 clks LRCK SCLK SDIN1 LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB
DAC_A1 32 clks
DAC_B1 32 clks
DAC_A2 32 clks
DAC_B2 32 clks
DAC_A3 32 clks
DAC_B3 32 clks
DAC_A4 32 clks
DAC_B4 32 clks
Data MSB LSB zero
Figure 19. Format 12 - TDM Mode
4.4
Oversampling Modes
The CS4385 operates in one of three oversampling modes based on the input sample rate. Mode selection is determined by the M4, M3 and M2 pins in Hardware Mode or the FM bits in Software Mode. Single-Speed mode supports input sample rates up to 50 kHz and uses a 128x oversampling ratio. Double-Speed Mode supports input sample rates up to 100 kHz and uses an oversampling ratio of 64x. Quad-Speed Mode supports input sample rates up to 200 kHz and uses an oversampling ratio of 32x. The auto-speed mode detect feature allows for the automatic selection of speed mode based off of the incoming sample rate. This allows the CS4385 to accept a wide range of sample rates with no external intervention necessary. The auto-speed mode detect feature is available in both hardware and Software Mode.
4.5
Interpolation Filter
To accommodate the increasingly complex requirements of digital audio systems, the CS4385 incorporates selectable interpolation filters for each mode of operation. A "fast" and a "slow" roll-off filter is available in each of Single, Double, and Quad-Speed modes. These filters have been designed to accommodate a variety of musical tastes and styles. The FILT_SEL bit is used to select which filter is used (see the "Filter Plots" on page 48 for more details). When in Hardware Mode, only the "fast" roll-off filter is available. Filter specifications can be found in Section 1, and filter response plots can be found in Figures 28 to 51.
26
DS671F1
CS4385
4.6 De-Emphasis
The CS4385 includes on-chip digital de-emphasis filters. The de-emphasis feature is included to accommodate older audio recordings that utilize pre-emphasis equalization as a means of noise reduction. Figure 20 shows the de-emphasis curve. The frequency response of the de-emphasis curve will scale proportionally with changes in sample rate, Fs if the input sample rate does not match the coefficient which has been selected. In Software Mode the required de-emphasis filter coefficients for 32 kHz, 44.1 kHz, or 48 kHz are selected via the de-emphasis control bits. In Hardware Mode only the 44.1 kHz coefficient is available (enabled through the M2 pin). If the input sample rate is not 44.1 kHz and de-emphasis has been selected then the corner frequencies of the de-emphasis filter will be scaled by a factor of the actual Fs over 44,100.
Gain dB T1=50 s 0dB
T2 = 15 s
-10dB
F1 3.183 kHz
F2 Frequency 10.61 kHz
Figure 20. De-Emphasis Curve
4.7
ATAPI Specification
The CS4385 implements the channel-mixing functions of the ATAPI CD-ROM specification. The ATAPI functions are applied per A-B pair. Refer to Table 9 on page 45 and Figure 21 for additional information.
Left Channel Audio Data
A Channel Volume Control
MUTE
Aout Ax
SDINx
Right Channel Audio Data
B Channel Volume Control
MUTE
AoutBx
Figure 21. ATAPI Block Diagram (x = channel pair 1, 2, 3, or 4)
DS671F1
27
CS4385
4.8 Direct Stream Digital (DSD) Mode
In Software Mode, the DSD/PCM bits (Reg. 02h) are used to configure the device for DSD Mode. The DSD_DIF bits (Reg 04h) then control the expected DSD rate and MCLK ratio. The DIR_DSD bit (Reg 04h) selects between two proprietary methods for DSD-to-analog conversion. The first method uses a decimation-free DSD processing technique which allows for features such as matched PCM-level output, DSD volume control, and 50kHz on-chip filter. The second method sends the DSD data directly to the on-chip switched-capacitor filter for conversion (without the above-mentioned features). The DSD_PM_EN bit (Reg. 04h) selects Phase Modulation (data plus data inverted) as the style of data input. In this mode, the DSD_PM_mode bit selects whether a 128Fs or 64x clock is used for phase modulated 64x data (see Figure 22). Use of Phase Modulation Mode may not directly affect the performance of the CS4385, but may lower the sensitivity to board-level routing of the DSD data signals. The CS4385 can detect errors in the DSD data which does not comply with the SACD specification. The STATIC_DSD and INVALID_DSD bits (Reg. 04h) allow the CS4385 to alter the incoming invalid DSD data. Depending on the error, the data may either be attenuated or replaced with a muted DSD signal (the MUTEC pins would be set according to the DAMUTE bit (Reg. 08h)). More information for any of these register bits can be found in Section 7. "Filter Plots" on page 48. The DSD input structure and analog outputs are designed to handle a nominal 0 dB-SACD (50% modulation index) at full rated performance. Signals of +3 dB-SACD may be applied for brief periods of time, however; performance at these levels is not guaranteed. If sustained +3 dB-SACD levels are required, the digital volume control should be set to -3.0 dB. This same volume control register affects PCM output levels. There is no need to change the volume control setting between PCM and DSD in order to have the 0dB output levels match (both 0 dBFS and 0 dB-SACD will output at -3 dB in this case).
DSD Normal Mode
Not Used
DSD Phase Modulation Mode DSD_SCLK BCKA (128Fs)
BCKA (64Fs)
DSD_SCLK
DSD_SCLK
BCKD (64Fs)
Not Used
D0
D1
D1
D2
DSDAx, DSDBx
DSDAx, DSDBx
D0
D1
D2
Not Used
Figure 22. DSD Phase Modulation Mode Diagram
28
DS671F1
CS4385
4.9 Grounding and Power Supply Arrangements
As with any high-resolution converter, the CS4385 requires careful attention to power supply and grounding arrangements if its potential performance is to be realized. The Typical Connection Diagram shows the recommended power arrangements, with VA, VD, VLC, and VLS connected to clean supplies. If the ground planes are split between digital ground and analog ground, the GND pins of the CS4385 should be connected to the analog ground plane. All signals, especially clocks, should be kept away from the FILT+ and VQ pins in order to avoid unwanted coupling into the DAC.
4.9.1
Capacitor Placement
Decoupling capacitors should be placed as close to the DAC as possible, with the low value ceramic capacitor being the closest. To further minimize impedance, these capacitors should be located on the same layer as the DAC. If desired, all supply pins with similar voltage ratings may be connected to the same supply, but a decoupling capacitor should still be placed on each supply pin. Notes: All decoupling capacitors should be referenced to ground.
The CDB4385 evaluation board demonstrates the optimum layout and power supply arrangements.
4.10
Analog Output and Filtering
The application note "Design Notes for a 2-Pole Filter with Differential Input" discusses the second-order Butterworth filter and differential to single-ended converter which was implemented on the CS4385 evaluation board, CDB4385, as seen in Figure 24. The CS4385 does not include phase or amplitude compensation for an external filter. Therefore, the DAC system phase and amplitude response will be dependent on the external analog circuitry. The off-chip filter has been designed to attenuate the typical full-scale output level to below 2 Vrms. Figure 23 shows how the full-scale differential analog output level specification is derived.
4.15 V AOUT+ 2.5 V 0.85 V 4.15 V AOUT2.5 V 0.85 V Full-Scale Output Level= (AOUT+) - (AOUT-)= 6.6 Vpp
Figure 23. Full-Scale Output
DS671F1
29
CS4385
Figure 24. Recommended Output Filter
4.11
The MUTEC Outputs
The MUTEC1 and MUTEC234 pins have an auto-polarity detect feature. The MUTEC output pins are high impedance at the time of reset. The external mute circuitry needs to be self-biased into an active state in order to be muted during reset. Upon release of reset, the CS4385 will detect the status of the MUTEC pins (high or low) and will then select that state as the polarity to drive when the mutes become active. The external-bias voltage level that the MUTEC pins see at the time of release of reset must meet the "MUTEC auto-detect input high/low voltage" specifications as outlined in the Digital Characteristics section. Figure 25 shows a single example of both an active high and an active low mute drive circuit. In these designs, the pull-up and pull-down resistors have been especially chosen to meet the input high/low threshold when used with the MMUN2111 and MMUN2211 internal bias resistances of 10 k. Use of the Mute Control function is not mandatory, but recommended, for designs requiring the absolute minimum in extraneous clicks and pops. Also, use of the Mute Control function can enable the system designer to achieve idle channel noise/signal-to-noise ratios which are only limited by the external mute circuit.
30
DS671F1
CS4385
Figure 25. Recommended Mute Circuitry
4.12
Recommended Power-Up Sequence
4.12.1 Hardware Mode
1. Hold RST low until the power supplies and configuration pins are stable, and the master and left/right clocks are locked to the appropriate frequencies, as discussed in Section 4.1. In this state, the registers are reset to the default settings, FILT+ will remain low, and VQ will be connected to VA/2. If RST can not be held low long enough the SDINx pins should remain static low until all other clocks are stable, and if possible the RST should be toggled low again once the system is stable. 2. Bring RST high. The device will remain in a low power state with FILT+ low and will initiate the Hardware power-up sequence after approximately 512 LRCK cycles in Single-Speed Mode (1024 LRCK cycles in Double-Speed Mode, and 2048 LRCK cycles in Quad-Speed Mode).
DS671F1
31
CS4385
4.12.2 Software Mode
1. Hold RST low until the power supply is stable, and the master and left/right clocks are locked to the appropriate frequencies, as discussed in Section 4.1. In this state, the registers are reset to the default settings, FILT+ will remain low, and VQ will be connected to VA/2. 2. Bring RST high. The device will remain in a low power state with FILT+ low for 512 LRCK cycles in Single-Speed Mode (1024 LRCK cycles in Double-Speed Mode, and 2048 LRCK cycles in QuadSpeed Mode). 3. In order to reduce the chances of clicks and pops, perform a write to the CP_EN bit prior to the completion of approximately 512 LRCK cycles in Single-Speed Mode (1024 LRCK cycles in DoubleSpeed Mode, and 2048 LRCK cycles in Quad-Speed Mode). The desired register settings can be loaded while keeping the PDN bit set to 1. Set the RMP_UP and RMP_DN bits to 1; then set the format and mode control bits to the desired settings. If more than the stated range of LRCK cycles passes before CPEN bit is written, the chip will enter Hardware Mode and begin to operate with the M0-M4 as the mode settings. CPEN bit may be written at anytime, even after the Hardware sequence has begun. It is advised that if the CPEN bit cannot be set in time, the SDINx pins should remain static low (this way no audio data can be converted incorrectly by the Hardware Mode settings). 4. Set the PDN bit to 0. This will initiate the power-up sequence, which lasts approximately 50 s.
4.13
Recommended Procedure for Switching Operational Modes
For systems where the absolute minimum in clicks and pops is required, it is recommended that the MUTE bits are set prior to changing significant DAC functions (such as changing sample rates or clock sources). The mute bits may then be released after clocks have settled and the proper modes have been set. It is required to have the device held in reset if the minimum high/low time specs of MCLK cannot be met during clock source changes.
4.14
Control Port Interface
The control port is used to load all the internal register settings in order to operate in Software Mode (see Section 7. "Filter Plots" on page 48). The operation of the control port may be completely asynchronous with the audio sample rate. However, to avoid potential interference problems, the control port pins should remain static if no operation is required. The control port operates in one of two modes: IC or SPI.
4.14.1 MAP Auto Increment
The device has MAP (memory address pointer) auto-increment capability enabled by the INCR bit (also the MSB) of the MAP. If INCR is set to 0, MAP will stay constant for successive IC writes or reads and SPI writes. If INCR is set to 1, MAP will auto-increment after each byte is written, allowing block reads or writes of successive registers.
4.14.2 IC Mode
In the IC Mode, data is clocked into and out of the bi-directional serial control data line, SDA, by the serial control port clock, SCL (see Figure 26 for the clock to data relationship). There is no CS pin. The AD0 pin enables the user to alter the chip address (001100[AD0][R/W]) and should be tied to VLC or GND, as required, before powering up the device. If the device ever detects a high-to-low transition on the AD0/CS pin after power-up, SPI Mode will be selected.
32
DS671F1
CS4385
4.14.2.1 IC WriteTM
To write to the device, follow the procedure below while adhering to the control port Switching Specifications in Section 1. 1. Initiate a START condition to the IC bus followed by the address byte. The upper 6 bits must be 001100. The seventh bit must match the setting of the AD0 pin, and the eighth must be 0. The eighth bit of the address byte is the R/W bit. 2. Wait for an acknowledge (ACK) from the part, then write to the memory address pointer, MAP. This byte points to the register to be written. 3. Wait for an acknowledge (ACK) from the part, then write the desired data to the register pointed to by the MAP. 4. If the INCR bit (see Section 4.14.1) is set to 1, repeat the previous step until all the desired registers are written, then initiate a STOP condition to the bus. 5. If the INCR bit is set to 0 and further IC writes to other registers are desired, it is necessary to initiate a repeated START condition and follow the procedure detailed from step 1. If no further writes to other registers are desired, initiate a STOP condition to the bus.
4.14.2.2 IC Read
To read from the device, follow the procedure below while adhering to the control port Switching Specifications. 1. Initiate a START condition to the IC bus followed by the address byte. The upper 6 bits must be 001100. The seventh bit must match the setting of the AD0 pin, and the eighth must be 1. The eighth bit of the address byte is the R/W bit. 2. After transmitting an acknowledge (ACK), the device will then transmit the contents of the register pointed to by the MAP. The MAP register will contain the address of the last register written to the MAP, or the default address (see Section 4.14.1) if an IC read is the first operation performed on the device. 3. Once the device has transmitted the contents of the register pointed to by the MAP, issue an ACK. 4. If the INCR bit is set to 1, the device will continue to transmit the contents of successive registers. Continue providing a clock and issue an ACK after each byte until all the desired registers are read, then initiate a STOP condition to the bus. 5. If the INCR bit is set to 0 and further IC reads from other registers are desired, it is necessary to initiate a repeated START condition and follow the procedure detailed from steps 1 and 2 from the IC Write instructions followed by step 1 of the IC Read section. If no further reads from other registers are desired, initiate a STOP condition to the bus.
N ote 1 SDA
001100 ADDR AD 0 R/W ACK DATA 1-8 ACK DATA 1-8 ACK
SCL Start Stop
N ote: If operation is a w rite, th is byte contain s the M em o ry A ddress P ointer, M A P.
Figure 26. Control Port Timing, IC Mode
DS671F1
33
CS4385
4.14.3 SPITM Mode
In SPI Mode, data is clocked into the serial control data line, CDIN, by the serial control port clock, CCLK (see Figure 27 for the clock to data relationship). There is no AD0 pin. Pin CS is the chip select signal and is used to control SPI writes to the control port. When the device detects a high to low transition on the AD0/CS pin after power-up, SPI Mode will be selected. All signals are inputs and data is clocked in on the rising edge of CCLK.
4.14.3.1 SPI Write
To write to the device, follow the procedure below while adhering to the control port Switching Specifications in Section 1. 1. Bring CS low. 2. The address byte on the CDIN pin must then be 00110000. 3. Write to the memory address pointer, MAP. This byte points to the register to be written. 4. Write the desired data to the register pointed to by the MAP. 5. If the INCR bit (see Section 4.14.1) is set to 1, repeat the previous step until all the desired registers are written, then bring CS high. 6. If the INCR bit is set to 0 and further SPI writes to other registers are desired, it is necessary to bring CS high, and follow the procedure detailed from step 1. If no further writes to other registers are desired, bring CS high.
CS CCLK CHIP ADDRESS C DIN
0011000
R/W
MAP
MSB
DATA
LSB
byte 1 M AP = M em ory Address Pointer
byte n
Figure 27. Control Port Timing, SPI Mode
4.15
Memory Address Pointer (MAP)
7 INCR 0 6 Reserved 0 5 Reserved 0 4 MAP4 0 3 MAP3 0 2 MAP2 0 1 MAP1 0 0 MAP0 0
4.15.1 INCR (Auto Map Increment Enable)
Default = `0' 0 - Disabled 1 - Enabled
4.15.2 MAP4-0 (Memory Address Pointer)
Default = `00000'
34
DS671F1
CS4385 5. REGISTER QUICK REFERENCE
Addr
01h 02h 03h 04h
Function
Chip Revision default Mode Control default PCM Control default DSD Control default
7
PART4 0 CPEN 0 DIF3 0
6
PART3 0 FREEZE 0 DIF2 0
5
PART2 0 0 DIF1 0
4
PART1 0 0 DIF0 0
3
PART0 1 0 Reserved 0
2
REV x 0 Reserved 0
1
REV x 0 FM1 1
0
REV x PDN 1 FM0 1
DSD/PCM DAC4_DIS DAC3_DIS DAC2_DIS DAC1_DIS
DSD_DIF2 DSD_DIF1 DSD_DIF0 DIR_DSD 0 Reserved 0 INV_B4 0 Reserved 0 SZC1 1 0 Reserved 0 A1_VOL7 0 B1_VOL7 0 Reserved 0 A2_VOL7 0 B2_VOL7 0 Reserved 0 A3_VOL7 0 B3_VOL7 0 Reserved 0 0 Reserved 0 INV_A4 0 MUTEC 0 SZC0 0 0 P1_DEM1 0 A1_VOL6 0 B1_VOL6 0 P2_DEM1 0 A2_VOL6 0 B2_VOL6 0 P3_DEM1 0 A3_VOL6 0 B3_VOL6 0 P4_DEM1 0 0 Reserved 0 INV_B3 0 Reserved 0 RMP_UP 1 0 P1_DEM0 0 A1_VOL5 0 B1_VOL5 0 P2_DEM0 0 A2_VOL5 0 B2_VOL5 0 P3_DEM0 0 A3_VOL5 0 B3_VOL5 0 P4_DEM0 0 0 Reserved 0 INV_A3 0 P1_A=B 0 RMP_DN 1 0 P1ATAPI4 0 A1_VOL4 0 B1_VOL4 0 P2ATAPI4 0 A2_VOL4 0 B2_VOL4 0 P3ATAPI4 0 A3_VOL4 0 B3_VOL4 0 P4ATAPI4 0
STATIC_D INVALID_D DSD_PM_ DSD_PM_ SD SD MD EN 1 Reserved 0 INV_B2 0 P2_A=B 0 PAMUTE 1 0 P1ATAPI3 1 A1_VOL3 0 B1_VOL3 0 P2ATAPI3 1 A2_VOL3 0 B2_VOL3 0 P3ATAPI3 1 A3_VOL3 0 B3_VOL3 0 P4ATAPI3 1 0 Reserved 0 INV_A2 0 P3_A=B 0 DAMUTE 1 MUTE_A2 0 P1ATAPI2 0 A1_VOL2 0 B1_VOL2 0 P2ATAPI2 0 A2_VOL2 0 B2_VOL2 0 P3ATAPI2 0 A3_VOL2 0 B3_VOL2 0 P4ATAPI2 0 0 Reserved 0 INV_B1 0 P4_A=B 0 MUTE_P1 0 MUTE_B1 0 P1ATAPI1 0 A1_VOL1 0 B1_VOL1 0 P2ATAPI1 0 A2_VOL1 0 B2_VOL1 0 P3ATAPI1 0 A3_VOL1 0 B3_VOL1 0 P4ATAPI1 0 0 FILT_SEL 0 INV_A1 0 SNGLVOL 0 MUTE_P0 0 MUTE_A1 0 P1ATAPI0 1 A1_VOL0 0 B1_VOL0 0 P2ATAPI0 1 A2_VOL0 0 B2_VOL0 0 P3ATAPI0 1 A3_VOL0 0 B3_VOL0 0 P4ATAPI0 1
05h 06h 07h 08h 09h
Filter Control default Invert Control default Group Control default Ramp and Mute default Mute Control default
MUTE_B4 MUTE_A4 MUTE_B3 MUTE_A3 MUTE_B2
0Ah Mixing Control Pair 1 (AOUTx1) default 0Bh Vol. Control A1 default 0Ch Vol. Control B1 default 0Dh Mixing Control Pair 2 (AOUTx1) default 0Eh Vol. Control A2 default 0Fh 10h Vol. Control B2 default Mixing Control Pair 3 (AOUTx1) default 11h 12h 13h Vol. Control A3 default Vol. Control B3 default Mixing Control Pair 4 (AOUTx1) default
DS671F1
35
CS4385
Addr
14h 15h 16h
Function
Vol. Control A4 default Vol. Control B4 default default
7
A4_VOL7 0 B4_VOL7 0 0
6
A4_VOL6 0 B4_VOL6 0 Reserved 0
5
A4_VOL5 0 B4_VOL5 0 MCLKDIV 0
4
A4_VOL4 0 B4_VOL4 0 Reserved 0
3
A4_VOL3 0 B4_VOL3 0 Reserved 0
2
A4_VOL2 0 B4_VOL2 0 Reserved 0
1
A4_VOL1 0 B4_VOL1 0 Reserved 0
0
A4_VOL0 0 B4_VOL0 0 Reserved 0
PCM clock mode Reserved
36
DS671F1
CS4385 6.
Note:
REGISTER DESCRIPTION
All registers are read/write in IC Mode and write only in SPI, unless otherwise noted.
6.1
7
Chip Revision (address 01h)
6 5 4 3 2 1 0
PART4 0
PART3 0
PART2 0
PART1 0
PART0 1
REV2 -
REV1 -
REV0 -
6.1.1 Part Number ID (PART) [Read Only]
00001- CS4385 Revision ID (REV) [Read Only] 000 - Revision A0 001 - Revision B0 Function: This read-only register can be used to identify the model and revision number of the device.
6.2
7
Mode Control 1 (address 02h)
6 5 4 3 2 1 0
CPEN 0
FREEZE 0
DSD/PCM 0
DAC4_DIS 0
DAC3_DIS 0
DAC2_DIS 0
DAC1_DIS 0
PDN 1
6.2.1 Control Port Enable (CPEN)
Default = 0 0 - Disabled 1 - Enabled Function: This bit defaults to 0, allowing the device to power-up in Stand-Alone Mode. The Control Port Mode can be accessed by setting this bit to 1. This will allow the operation of the device to be controlled by the registers, and the pin definitions will conform to Control Port Mode. To accomplish a clean power-up, the user should write this bit within 10 ms following the release of Reset.
6.2.2 Freeze Controls (FREEZE)
Default = 0 0 - Disabled 1 - Enabled Function: This function allows modifications to be made to the registers without the changes taking effect until the FREEZE is disabled. To make multiple changes in the Control port registers take effect simultaneously, enable the FREEZE Bit, make all register changes, then Disable the FREEZE bit.
DS671F1
37
CS4385
6.2.3 PCM/DSD Selection (DSD/PCM)
Default = 0 0 - PCM 1 - DSD Function: This function selects DSD or PCM Mode. The appropriate data and clocks should be present before changing modes, or else MUTE should be selected.
6.2.4 DAC Pair Disable (DACx_DIS)
Default = 0 0 - Enabled 1 - Disabled Function: When enabled, the respective DAC channel pairx (AOUTAx and AOUTBx) will remain in a reset state. It is advised that changes to these bits be made while the power-down bit is enabled to eliminate the possibility of audible artifacts.
6.2.5 Power Down (PDN)
Default = 1 0 - Disabled 1 - Enabled Function: The entire device will enter a low-power state when this function is enabled, and the contents of the control registers are retained in this mode. The power-down bit defaults to `enabled' on power-up and must be disabled before normal operation in Control Port Mode can occur.
6.3
7
PCM Control (address 03h)
6 5 4 3 2 1 0
DIF3 0
DIF2 0
DIF1 0
DIF0 0
Reserved 0
Reserved 0
FM1 1
FM0 1
6.3.1 Digital Interface Format (DIF)
Default = 0000 - Format 0 (Left-Justified, up to 24-bit data) Function: These bits select the interface format for the serial audio input. The DSD/PCM bit determines whether PCM or DSD Mode is selected. The required relationship between the Left/Right clock, serial clock and serial data is defined by the Digital Interface Format and the options are detailed in Figures 9 through through 21.
38
DS671F1
CS4385
DIF3
0 0 0 0 0 0 1 1 1 1 1 X
DIF2
0 0 0 0 1 1 0 0 0 0 1 X
DIF1
0 0 1 1 0 0 0 0 1 1 0 X
DIF0
0 1 0 1 0 1 0 1 0 1 0 X
DESCRIPTION
Left-Justified, up to 24-bit data IS, up to 24-bit data Right-Justified, 16-bit data Right-Justified, 24-bit data Right-Justified, 20-bit data Right-Justified, 18-bit data One-Line Mode 1, 24-bit Data +SDIN4 One-Line Mode 2, 20-bit Data +SDIN4
FORMAT
0 1 2 3 4 5 8 9 10 11 12
One-Line Mode 3, 24-bit 6-channel One-Line Mode 4, 20-bit 6-channel
TDM All other combinations are Reserved
Table 7. Digital Interface Formats - PCM Mode
6.3.2 Functional Mode (FM)
Default = 11 00 - Single-Speed Mode (4 to 50 kHz sample rates) 01 - Double-Speed Mode (50 to 100 kHz sample rates) 10 - Quad-Speed Mode (100 to 200 kHz sample rates) 11 - Auto Speed Mode detect (32 kHz to 200 kHz sample rates) Function: Selects the required range of input sample rates or Auto Speed Mode.
6.4
7
DSD Control (address 04h)
6 5 4 3 2 1 0
DSD_DIF2 0
DSD_DIF1 0
DSD_DIF0 0
DIR_DSD 0
STATIC_DSD INVALID_DSD DSD_PM_MD DSD_PM_EN 1 1 0 0
6.4.1 DSD Mode Digital Interface Format (DSD_DIF)
Default = 000 - Format 0 (64x oversampled DSD data with a 4x MCLK to DSD data rate) Function: The relationship between the oversampling ratio of the DSD audio data and the required Master clock-toDSD-data rate is defined by the Digital Interface Format pins. The DSD/PCM bit determines whether PCM or DSD Mode is selected. DIF2 DIF1 DIFO DESCRIPTION
0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 64x oversampled DSD data with a 4x MCLK to DSD data rate 64x oversampled DSD data with a 6x MCLK to DSD data rate 64x oversampled DSD data with a 8x MCLK to DSD data rate 64x oversampled DSD data with a 12x MCLK to DSD data rate 128x oversampled DSD data with a 2x MCLK to DSD data rate 128x oversampled DSD data with a 3x MCLK to DSD data rate 128x oversampled DSD data with a 4x MCLK to DSD data rate 128x oversampled DSD data with a 6x MCLK to DSD data rate
Table 8. Digital Interface Formats - DSD Mode
DS671F1
39
CS4385
6.4.2 Direct DSD Conversion (DIR_DSD)
Function: When set to 0 (default), DSD input data is sent to the DSD processor for filtering and volume control functions. When set to 1, DSD input data is sent directly to the switched capacitor DACs for a pure DSD conversion. In this mode, the full-scale DSD and PCM levels will not be matched (see Section 1), the dynamic range performance may be reduced, the volume control is inactive, and the 50 kHz low pass filter is not available (see Section 1 for filter specifications).
6.4.3 Static DSD Detect (STATIC_DSD)
Function: When set to 1 (default), the DSD processor checks for 28 consecutive zeroes or ones and, if detected, sends a mute signal to the DACs. The MUTEC pins will eventually go active according to the DAMUTE register. When set to 0, this function is disabled.
6.4.4 Invalid DSD Detect (INVALID_DSD)
Function: When set to 1, the DSD processor checks for greater than 24 out of 28 bits of the same value and, if detected, will attenuate the data sent to the DACs. The MUTEC pins go active according to the DAMUTE register. When set to 0 (default), this function is disabled.
6.4.5 DSD Phase Modulation Mode Select (DSD_PM_MODE)
Function: When set to 0 (default), the 128Fs (BCKA) clock should be input to DSD_SCLK for Phase Modulation Mode. (See Figure 22 on page 28) When set to 1, the 64Fs (BCKD) clock should be input to DSD_SCLK for Phase Modulation Mode.
6.4.6 DSD Phase Modulation Mode Enable (DSD_PM_EN)
Function: When set to 1, DSD phase modulation input mode is enabled, and the DSD_PM_MODE bit should be set accordingly. When set to 0 (default), this function is disabled (DSD normal mode).
40
DS671F1
CS4385
6.5
7
Filter Control (address 05h)
6 5 4 3 2 1 0
Reserved 0
Reserved 0
Reserved 0
Reserved 0
Reserved 0
Reserved 0
Reserved 0
FILT_SEL 0
6.5.1 Interpolation Filter Select (FILT_SEL)
Function: When set to 0 (default), the Interpolation Filter has a fast roll-off. When set to 1, the Interpolation Filter has a slow roll-off. The specifications for each filter can be found in the Analog characteristics table, and response plots can be found in Figures 28 to 51.
6.6
7
Invert Control (address 06h)
6 5 4 3 2 1 0
INV_B4 0
INV_A4 0
INV_B3 0
INV_A3 0
INV_B2 0
INV_A2 0
INV_B1 0
INV_A1 0
6.6.1 Invert Signal Polarity (Inv_xx)
Function: When set to 1, this bit inverts the signal polarity of channel xx. When set to 0 (default), this function is disabled.
6.7
7
Group Control (address 07h)
6 5 4 3 2 1 0
Reserved 0
MUTEC 0
Reserved 0
P1_A=B 0
P2_A=B 0
P3_A=B 0
P4_A=B 0
SNGLVOL 0
6.7.1 Mutec Pin Control (MUTEC)
Default = 0 0 - Two Mute control signals 1 - Single mute control signal on MUTEC1 Function: Selects how the internal mute signals are routed to the MUTEC1 and MUTEC234 pins. When set to `0', a logical AND of DAC pair 1 mute control signals are output on MUTEC1 and a logical AND of the mute control signals of DAC pairs 2, 3, and 4 are output on MUTEC234. When set to `1', a logical AND of all DAC pair mute control signals is output on the MUTEC1 pin, MUTEC234 will remain static. For more information on the use of the mute control function see the MUTEC1 and MUTEC234 pins in Section 4.11.
DS671F1
41
CS4385
6.7.2 Channel A Volume = Channel B Volume (Px_A=B)
Default = 0 0 - Disabled 1 - Enabled Function: The AOUTAx and AOUTBx volume levels are independently controlled by the A and the B Channel Volume Control Bytes when this function is disabled. The volume on both AOUTAx and AOUTBx are determined by the A Channel Attenuation and Volume Control Bytes (per A-B pair), and the B Channel Bytes are ignored when this function is enabled.
6.7.3 Single Volume Control (SNGLVOL)
Default = 0 0 - Disabled 1 - Enabled Function: The individual channel volume levels are independently controlled by their respective Volume Control Bytes when this function is disabled. The volume on all channels is determined by the A1 Channel Volume Control Byte, and the other Volume Control Bytes are ignored when this function is enabled.
6.8
7
Ramp and Mute (address 08h)
6 5 4 3 2 1 0
SZC1 1
SZC0 0
RMP_UP 1
RMP_DN 1
PAMUTE 1
DAMUTE 1
MUTE_P1 0
MUTE_P0 0
6.8.1 Soft Ramp and Zero Cross CONTROL (SZC)
Default = 10 00 - Immediate Change 01 - Zero Cross 10 - Soft Ramp 11 - Soft Ramp on Zero Crossings Function: Immediate Change When Immediate Change is selected, all level changes will take effect immediately in one step. Zero Cross Zero Cross Enable dictates that signal-level changes, either by attenuation changes or muting, will occur on a signal zero crossing to minimize audible artifacts. The requested level change will occur after a timeout period between 512 and 1024 sample periods (10.7 ms to 21.3 ms at 48 kHz sample rate) if the signal does not encounter a zero crossing. The zero cross function is independently monitored and implemented for each channel. Soft Ramp Soft Ramp allows level changes, both muting and attenuation, to be implemented by incrementally ramping, in 1/8 dB steps, from the current level to the new level at a rate of 1 dB per 8 left/right clock periods.
42
DS671F1
CS4385
Soft Ramp on Zero Crossing Soft Ramp and Zero Cross Enable dictates that signal-level changes, either by attenuation changes or muting, will occur in 1/8 dB steps and be implemented on a signal zero crossing. The 1/8 dB level change will occur after a timeout period between 512 and 1024 sample periods (10.7 ms to 21.3 ms at 48 kHz sample rate) if the signal does not encounter a zero crossing. The zero cross function is independently monitored and implemented for each channel.
6.8.2 Soft Volume Ramp-Up after Error (RMP_UP)
Function: An un-mute will be performed after executing an LRCK/MCLK ratio change or error, and after changing the Functional Mode. When set to 1 (default), this unmute is effected, similar to attenuation changes, by the Soft and Zero Cross bits in the Volume and Mixing Control register. When set to 0, an immediate unmute is performed in these instances. Note: For best results, it is recommended that this feature be used in conjunction with the RMP_DN bit.
6.8.3 Soft Ramp-Down before Filter Mode Change (RMP_DN)
Function: If either the FILT_SEL or DEM bits are changed the DAC will stop conversion for a period of time to change its filter values. This bit selects how the data is effected prior to and after the change of the filter values. When set to 1 (default), a mute will be performed prior to executing a filter mode change and an un-mute will be performed after executing the filter mode change. This mute and un-mute are effected, similar to attenuation changes, by the Soft and Zero Cross bits in the Volume and Mixing Control register. When set to 0, an immediate mute is performed prior to executing a filter mode change. Note: For best results, it is recommended that this feature be used in conjunction with the RMP_UP bit.
6.8.4 PCM Auto-Mute (PAMUTE)
Function: When set to 1 (default), the Digital-to-Analog converter output will mute following the reception of 8192 consecutive audio samples of static 0 or -1. A single sample of non-static data will release the mute. Detection and muting is done independently for each channel. The quiescent voltage on the output will be retained and the Mute Control pin will go active during the mute period. When set to 0, this function is disabled.
DS671F1
43
CS4385
6.8.5 DSD Auto-Mute (DAMUTE)
Function: When set to 1 (default), the Digital-to-Analog converter output will mute following the reception of 256 repeated 8-bit DSD mute patterns (as defined in the SACD specification). A single bit not fitting the repeated mute pattern (mentioned above) will release the mute. Detection and muting is done independently for each channel. The quiescent voltage on the output will be retained, and the Mute Control pin will go active during the mute period.
6.8.6 MUTE Polarity and DETECT (MUTEP1:0)
Default = 00 00 - Auto polarity detect, selected from MUTEC1 pin 01 - Reserved 10 - Active low mute polarity 11 - Active high mute polarity Function: Auto mute polarity detect (00) See Section 4.11 "The MUTEC Outputs" on page 30 for description. Active low mute polarity (10) When RST is low, the outputs are high impedance and will need to be biased active. Once reset has been released and after this bit is set, the MUTEC output pins will be active low polarity. Active high mute polarity (11) At reset time, the outputs are high impedance and will need to be biased active. Once reset has been released and after this bit is set, the MUTEC output pins will be active high polarity.
6.9
7
Mute Control (address 09h)
6 5 4 3 2 1 0
MUTE_B4 0
MUTE_A4 0
MUTE_B3 0
MUTE_A3 0
MUTE_B2 0
MUTE_A2 0
MUTE_B1 0
MUTE_A1 0
6.9.1 Mute (MUTE_xx)
Default = 0 0 - Disabled 1 - Enabled Function: The Digital-to-Analog converter output will mute when enabled. The quiescent voltage on the output will be retained. The muting function is affected, similarly to attenuation changes, by the Soft and Zero Cross bits. The MUTE pins will go active during the mute period according to the MUTEC bit.
44
DS671F1
CS4385
6.10
7
Mixing Control (address 0Ah, 0Dh, 10h, 13h)
6 5 4 3 2 1 0
Reserved 0
Px_DEM1 0
Px_DEM0 0
PxATAPI4 0
PxATAPI3 1
PxATAPI2 0
PxATAPI1 0
PxATAPI0 1
6.10.1 De-Emphasis Control (PX_DEM1:0)
Default = 00 00 - Disabled 01 - 44.1 kHz 10 - 48 kHz 11 - 32 kHz Function: Selects the appropriate digital filter to maintain the standard 15 s/50 s digital de-emphasis filter response at 32, 44.1 or 48 kHz sample rates. (see Figure 20) De-emphasis is only available in Single-Speed Mode.
6.11
ATAPI Channel Mixing and Muting (ATAPI)
Default = 01001 - AOUTAx=aL, AOUTBx=bR (Stereo) Function: The CS4385 implements the channel-mixing functions of the ATAPI CD-ROM specification. The ATAPI functions are applied per A-B pair. Refer to Table 9 and Figure 21 for additional information. ATAPI4
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1
ATAPI3
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0
ATAPI2
0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0
ATAPI1
0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1
ATAPI0
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
AOUTAx
MUTE MUTE MUTE MUTE aR aR aR aR aL aL aL aL a[(L+R)/2] a[(L+R)/2] a[(L+R)/2] a[(L+R)/2] MUTE MUTE MUTE
AOUTBx
MUTE bR bL b[(L+R)/2] MUTE bR bL b[(L+R)/2] MUTE bR bL b[(L+R)/2] MUTE bR bL b[(L+R)/2] MUTE bR bL
Table 9. ATAPI Decode Table
DS671F1
45
CS4385
ATAPI4
1 1 1 1 1 1 1 1 1 1 1 1 1
ATAPI3
0 0 0 0 0 1 1 1 1 1 1 1 1
ATAPI2
0 1 1 1 1 0 0 0 0 1 1 1 1
ATAPI1
1 0 0 1 1 0 0 1 1 0 0 1 1
ATAPI0
1 0 1 0 1 0 1 0 1 0 1 0 1
AOUTAx
MUTE aR aR aR aR aL aL aL aL [(aL+bR)/2] [(aL+bR)/2] [(bL+aR)/2] [(aL+bR)/2]
AOUTBx
[(bL+aR)/2] MUTE bR bL [(aL+bR)/2] MUTE bR bL [(aL+bR)/2] MUTE bR bL [(aL+bR)/2]
Table 9. ATAPI Decode Table
6.12
7
Volume Control (address 0Bh, 0Ch, 0Eh, 0Fh, 11h, 12h, 14h, 15h)
6 5 4 3 2 1 0
xx_VOL7 0
xx_VOL6 0
xx_VOL5 0
xx_VOL4 0
xx_VOL3 0
xx_VOL2 0
xx_VOL1 0
xx_VOL0 0
These eight registers provide individual volume and mute control for each of the eight channels. The values for "xx" in the bit fields above are as follows: Register address 0Bh - xx = A1 Register address 0Ch - xx = B1 Register address 0Eh - xx = A2 Register address 0Fh - xx = B2 Register address 11h - xx = A3 Register address 12h - xx = B3 Register address 14h - xx = A4 Register address 15h - xx = B4
6.12.1 Digital Volume Control (xx_VOL7:0)
Default = 00h (0 dB) Function: The Digital Volume Control registers allow independent control of the signal levels in 1/2 dB increments from 0 to -127.5 dB. Volume settings are decoded as shown in Table 10. The volume changes are implemented as dictated by the Soft and Zero Cross bits in the Power and Muting Control register. Note that the values in the volume setting column in Table 10 are approximate. The actual attenuation is determined by taking the decimal value of the volume register and multiplying by 6.02/12. Binary Code
00000000 00000001 00000110 11111111
Decimal Value
0 1 6 255
Volume Setting
0 dB -0.5 dB -3.0 dB -127.5 dB
Table 10. Example Digital Volume Settings
46
DS671F1
CS4385
6.13
7
PCM Clock Mode (address 16h)
6 5 4 3 2 1 0
Reserved 0
Reserved 0
MCLKDIV 0
Reserved 0
Reserved 0
Reserved 0
Reserved 0
Reserved 0
6.13.1 Master Clock DIVIDE by 2 ENABLE (MCLKDIV)
Function: When set to 1, the MCLKDIV bit enables a circuit which divides the externally applied MCLK signal by 2 prior to all other internal circuitry. When set to 0 (default), MCLK is unchanged.
DS671F1
47
CS4385 7. FILTER PLOTS
0 0
-20
-20
Amplitude (dB)
Amplitude (dB)
-40
-40
-60
-60
-80
-80
-100
-100
-120 0.4
0.5
0.6 0.7 0.8 Frequency(normalized to Fs)
0.9
1
-120 0.4
0.42
0.44
0.46
0.48 0.5 0.52 Frequency(normalized to Fs)
0.54
0.56
0.58
0.6
Figure 28. Single-Speed (fast) Stopband Rejection
0
Figure 29. Single-Speed (fast) Transition Band
0.02
-1
0.015
-2 0.01 -3 0.005
Amplitude (dB)
Amplitude (dB)
-4
-5
0
-6
-0.005
-7 -0.01 -8 -0.015
-9
-10 0.45
0.46
0.47
0.48
0.49 0.5 0.51 Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
-0.02
0
0.05
0.1
0.15
0.2 0.25 0.3 Frequency(normalized to Fs)
0.35
0.4
0.45
0.5
Figure 30. Single-Speed (fast) Transition Band (detail)
Figure 31. Single-Speed (fast) Passband Ripple
0
0
-20
-20
Amplitude (dB)
-60
Amplitude (dB)
-40
-40
-60
-80
-80
-100
-100
-120 0.4
0.5
0.6 0.7 0.8 Frequency(normalized to Fs)
0.9
1
-120 0.4
0.42
0.44
0.46
0.48 0.5 0.52 Frequency(normalized to Fs)
0.54
0.56
0.58
0.6
Figure 32. Single-Speed (slow) Stopband Rejection
Figure 33. Single-Speed (slow) Transition Band
48
DS671F1
CS4385
0 0.02
-1
0.015
-2 0.01 -3 0.005
Amplitude (dB)
Amplitude (dB)
-4
-5
0
-6
-0.005
-7 -0.01 -8 -0.015
-9
-10 0.45
0.46
0.47
0.48
0.49 0.5 0.51 Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
-0.02
0
0.05
0.1
0.15
0.2 0.25 0.3 Frequency(normalized to Fs)
0.35
0.4
0.45
0.5
Figure 34. Single-Speed (slow) Transition Band (detail)
Figure 35. Single-Speed (slow) Passband Ripple
0
0
20
20
Amplitude (dB)
Amplitude (dB)
40
40
60
60
80
80
100
100
120
120
0.4
0.5
0.6 0.7 0.8 Frequency(normalized to Fs)
0.9
1
0.4
0.42
0.44
0.46
0.48 0.5 0.52 Frequency(normalized to Fs)
0.54
0.56
0.58
0.6
Figure 36. Double-Speed (fast) Stopband Rejection
0
Figure 37. Double-Speed (fast) Transition Band
0.02
1
0.015
2
0.01
3
Amplitude (dB)
5
Amplitude (dB)
4
0.005
0
6
0.005
7
0.01
8
9
0.015
10 0.45
0.46
0.47
0.48
0.49 0.5 0.51 Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
0.02
0
0.05
0.1
0.15
0.2 0.25 0.3 Frequency(normalized to Fs)
0.35
0.4
0.45
0.5
Figure 38. Double-Speed (fast) Transition Band (detail)
Figure 39. Double-Speed (fast) Passband Ripple
DS671F1
49
CS4385
0
0
20
20
Amplitude (dB)
Amplitude (dB)
40
40
60
60
80
80
100
100
120
120
0.2
0.3
0.4
0.5 0.6 0.7 Frequency(normalized to Fs)
0.8
0.9
1
0.2
0.3
0.4 0.5 0.6 Frequency(normalized to Fs)
0.7
0.8
Figure 40. Double-Speed (slow) Stopband Rejection
0
Figure 41. Double-Speed (slow) Transition Band
0.02
1
0.015
2
0.01
3
0.005 Amplitude (dB)
Amplitude (dB)
4
5
0
6
0.005
7
0.01
8
0.015
9
10 0.45
0.46
0.47
0.48
0.49 0.5 0.51 Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
0.02
0
0.05
0.1
0.15 0.2 Frequency(normalized to Fs)
0.25
0.3
0.35
Figure 42. Double-Speed (slow) Transition Band (detail)
Figure 43. Double-Speed (slow) Passband Ripple
0
0
20
20
40 Amplitude (dB)
Amplitude (dB)
40
60
60
80
80
100
100
120
120
0.2
0.3
0.4
0.5 0.6 0.7 Frequency(normalized to Fs)
0.8
0.9
1
0.2
0.3
0.4 0.5 0.6 Frequency(normalized to Fs)
0.7
0.8
Figure 44. Quad-Speed (fast) Stopband Rejection
Figure 45. Quad-Speed (fast) Transition Band
50
DS671F1
CS4385
0
0.2
1
0.15
2
0.1
3
0.05
Amplitude (dB)
Amplitude (dB) 0.05 0.1 0.15 0.2
4
5
0
6
7
8
9
10 0.45
0.46
0.47
0.48
0.49 0.5 0.51 Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
0
0.05
0.1 0.15 Frequency(normalized to Fs)
0.2
0.25
Figure 46. Quad-Speed (fast) Transition Band (detail)
Figure 47. Quad-Speed (fast) Passband Ripple
0
0
20
20
Amplitude (dB)
Amplitude (dB)
40
40
60
60
80
80
100
100
120
120
0.1
0.2
0.3
0.4 0.5 0.6 0.7 Frequency(normalized to Fs)
0.8
0.9
1
0.1
0.2
0.3
0.4 0.5 0.6 Frequency(normalized to Fs)
0.7
0.8
0.9
Figure 48. Quad-Speed (slow) Stopband Rejection
0
Figure 49. Quad-Speed (slow) Transition Band
0.02
1
0.015
2
0.01
3
0.005 Amplitude (dB)
Amplitude (dB)
4
5
0
6
0.005
7
0.01
8
0.015
9
10 0.45
0.46
0.47
0.48
0.49 0.5 0.51 Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
0.02
0
0.02
0.04 0.06 0.08 Frequency(normalized to Fs)
0.1
0.12
Figure 50. Quad-Speed (slow) Transition Band (detail)
Figure 51. Quad-Speed (slow) Passband Ripple
DS671F1
51
CS4385 8. PARAMETER DEFINITIONS
Total Harmonic Distortion + Noise (THD+N) The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified bandwidth (typically 10 Hz to 20 kHz), including distortion components. Expressed in decibels. Dynamic Range The ratio of the full-scale rms value of the signal to the rms sum of all other spectral components over the specified bandwidth. Dynamic range is a signal-to-noise measurement over the specified bandwidth made with a -60 dBFS signal. 60 dB is then added to the resulting measurement to refer the measurement to full scale. This technique ensures that the distortion components are below the noise level and do not affect the measurement. This measurement technique has been accepted by the Audio Engineering Society, AES17-1991, and the Electronic Industries Association of Japan, EIAJ CP-307. Interchannel Isolation A measure of crosstalk between the left and right channels. Measured for each channel at the converter's output with all zeros to the input under test and a full-scale signal applied to the other channel. Units in decibels. Interchannel Gain Mismatch The gain difference between left and right channels. Units in decibels. Gain Drift The change in gain value with temperature. Units in ppm/C.
52
DS671F1
CS4385 9. PACKAGE DIMENSIONS 48L LQFP PACKAGE DRAWING
E E1
D D1
1
e
B
A A1
L
DIM
A A1 B D D1 E E1 e* L
MIN
--0.002 0.007 0.343 0.272 0.343 0.272 0.016 0.018 0.000
INCHES NOM
0.055 0.004 0.009 0.354 0.28 0.354 0.28 0.020 0.24 4
MAX
0.063 0.006 0.011 0.366 0.280 0.366 0.280 0.024 0.030 7.000
MIN
--0.05 0.17 8.70 6.90 8.70 6.90 0.40 0.45 0.00
MILLIMETERS NOM
1.40 0.10 0.22 9.0 BSC 7.0 BSC 9.0 BSC 7.0 BSC 0.50 BSC 0.60 4
MAX
1.60 0.15 0.27 9.30 7.10 9.30 7.10 0.60 0.75 7.00
* Nominal pin pitch is 0.50 mm
*Controlling dimension is mm.
*JEDEC Designation: MS022
DS671F1
53
CS4385 10.ORDERING INFORMATION
Product CS4385 CDB4385 Description 114 dB, 192 kHz 8channel D/A Converter CS4385 Evaluation Board Package 48-pin LQFP Pb-Free YES Container Tray Commercial -40 to +85 C Tape & Reel Tray Automotive -40 to +105 C Tape & Reel Grade Temp Range Order # CS4385-CQZ CS4385-CQZR CS4385-DQZ CS4385-DQZR CDB4385
11.REFERENCES
1. How to Achieve Optimum Performance from Delta-Sigma A/D & D/A Converters, by Steven Harris. Paper presented at the 93rd Convention of the Audio Engineering Society, October 1992. 2. Cirrus Logic datasheet CDB4385 available at http://www.cirrus.com 3. Design Notes for a 2-Pole Filter with Differential Input, by Steven Green. Cirrus Logic Application Note AN48 4. The IC-Bus Specification: Version 2.0, Philips Semiconductors, December 1998. http://www.semiconductors.philips.com
54
DS671F1
CS4385 12.REVISION HISTORY
Release Changes
Updated Guaranteed Operational Temperature Range in "Recommended Operating Conditions" on page 8. Updated VA, VLC, and VLS current cunsumption specs Updated Fullscale output level Updated Dynamic perforamnce limits. Removed VOH specification Updated VOL specificationUpdated TDM timing specs Updated "Recommended Operating Conditions" on page 8 Updated "DAC Analog Characteristics - Commercial (-CQZ)" on page 9 Updated "DAC Analog Characteristics - Automotive (-DQZ)" on page 10 Updated "Power and Thermal Characteristics" on page 11 Updated Legal Information on page 55
PP3
F1
Contacting Cirrus Logic Support
For all product questions and inquiries, contact a Cirrus Logic Sales Representative. To find the one nearest to you, go to www.cirrus.com
IMPORTANT NOTICE Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. IC is a registered trademark of Philips Semiconductor. SPI is a trademark of Motorola, Inc.
DS671F1
55

▲Up To Search▲

Price & Availability of CS438507

	To Download CS438507 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .